TMS374 ECU DECODER For Renault Peugeot Citroen Hyundai Kia Immo Killer

TMS374 ECU DECODER For Renault Peugeot Citroen Hyundai Kia Immo Killer

Tanpa Laptop bisa digunakan langsung
A handy tool to have that will decode an all the above ecu's to a new state without the need of a laptop!

Introduction:
This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz). This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC. A small MCU is used to generate the pulses instead of the PC RS232 Tx line.
The TMS 374 software is in fact a simple frequency sweeper with an effective range from about 2000Hz to about 100Hz. The Tiny sweeper does exactly the same but much more better (bigger range). After powering the device on - the LED should blink twice. Pressing the button will start the sweep procedure. LED ON - means there are pulses on the output. After reaching the lowest frequency the LED goes off and the mcu stops the generation.

Connection diagram:
+ : 12v DC
- : GND
S : signal wire

Manual:
After powering the device on - the LED should blink twice. The sweeping process starts as power is supplied to the device. LED ON - means there are pulses on the output. After reaching the lowest frequency the LED goes off and the mcu stops the generation.

* Connect the GND line to any suitable GND on the ECU via the small grabber.
* Connect the Data line to the Reset pin on the EPROM via the small grabber.
* Power the ECU and then the sweeper, the sweeper will flash twice on power up.
* Press the button and the device will start sweeping, once the LED turns off your done.
* Cut the immo data line on the ECU before re-fitting back to car.

TMS-374 Decoder ECU info
The sweeper should work with the following ECUs:

Renault SIEMENS Fenix 3 and 5
Renault Megane 1400cc 8v
Renault Megane 1600cc 8v
Renault Megane 2000cc 8v
Renault Megane 2000cc 16V
Renault Megane Scenic 1400cc 8v
Renault Megane Scenic 1600cc 8v
Renault Megane Scenic 2000cc 8v
Renault Sefrane 2000cc 16V
Renault Laguna 2000cc 8v
Renault Laguna 2000cc 16v
Renault Espace 2000cc 8v

Renault SAGEM SAFIR 1 and 2
Renault Clio 1200cc 8V
Renault Clio 1400cc 8V
Renault Clio 1600cc 8V
Renault Clio 2000cc 16V Williams
Renault Laguna 1800cc 8V
Renault Laguna 2000cc 8V
Renault Laguna 1800cc 16V
Renault Laguna 2000cc 16V
Renault Twingo 1200cc 8V

NOTE: If reset pin is connected to ground then it must be lifted or the track cut before decoding. This can be re-attached after decoding the ecu. As a rule of thumb keep the power connected to the ECU for a futher five minutes after the decoder has completed the decoding process.

Sagem SL96 Psa
Peugeot 306 1400cc 8V
Peugeot 306 1600cc 16V
Peugeot 306 1800 16V
Peugeot Ranch 1400 8V
Citroen Berlingo 1400cc 8V
Citroen Xrara 1400cc 8V
Citroen Xrara 1800cc 16V

DAEWOO SIEMENS
Daewoo Matiz 800cc

HYUNDAI SIEMENS
Hyundai Coupe 1600cc 16V
Hyundai Coupe 2000cc 16V

KIA SIEMENS
Kia Rio 1300 16V
Kia Rio 1500 16V

MAGNETI MARELLI
1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90,
Citroen Berlingo 1800cc 8V
Citroen Saxo 1400cc 8V
Citroen Saxo 1600cc 16V
Citroen Xara 1400cc 8V
Citroen Xara 1800cc 8V
Citroen Xara 2000cc 16V
Citroen ZX 1400cc 8V
Peugeot 106 1400cc 8V
Peugeot 106 1600cc 8V
Peugeot 106 1600cc 16V
Peugeot 206 1100cc 8V
Peugeot 206 1400cc 8V
Peugeot 306 1400cc 8V
Peugeot 306 1600cc 8V
Peugeot 306 1800cc 8V
Peugeot 405 1800cc 8V
Peugeot 406 1800cc 8V
Peugeot Partner 1800 8V


TMS-374 1AP\SAGEM\SIEMENS
Procedure:
Simply power the ECU and device using a suitable 12V power supply. Connect the GND cable to a good ground source on the ECU and then the data line to the Reset Pin on the flash 27c512 or28F512 as shown in the diagram.
Start the device and wait for it to finish its cycle (the led will turn off). At this point the ECU has been decoded and put into a new state. The Immo line will need to be disconnected before the ECU is re-fitted back to the car.

CENTRALINE SAGEM SAFIR RENAULT 35 PIN
PIN 18 --- 12v+
PIN 4\34 --- GND
PIN 30 Immo data line (cut)

CENTRALINE SAGEM SAFIR 1 RENAULT 55 PIN
PIN 1 --- 12v+
PIN 2\3\18 --- GND
PIN 37 Immo line (cut)



CENTRALINE SAGEM SAFIR 2 RENAULT 55 PIN
PIN 1 --- 12v+
PIN 2\3\18 --- GND
PIN 37 Immo data line (cut)


CENTRALINE SIEMENS DAEWOO (MATIZ) 55 PIN
PIN 32\24 --- 12V+
PIN 2\3 --- GND
PIN 11 Immo data line (cut)

CENTRALINE SIEMENS RENAULT 55 PIN
PIN 32\24\1 --- 12V+
PIN 2\3 --- GND
PIN 37 Immo data line on 1600 cc (cut)
PIN 35 Immo data line on 1800cc\2000 cc (cut)


CENTRALINE 1AP 55 PIN
PIN 35\13 --- 12v+
PIN 54\36 --- GND
PIN 27\48 Immo data line (cut)


CENTRALINE SIEMENS HUNDAY 55 PIN

CENTRALINE SAGEM SL96 PSA
Pin 1 --- 12v+
Pin 2\3\18 --- GND
Pin 27\48 Immo data line (cut)

TMS-374 ECU sweeper should work with the following ECUs:

Renault SIEMENS Fenix 3 and 5
Renault Megane 1400cc 8v
Renault Megane 1600cc 8v
Renault Megane 2000cc 8v
Renault Megane 2000cc 16V
Renault Megane Scenic 1400cc 8v
Renault Megane Scenic 1600cc 8v
Renault Megane Scenic 2000cc 8v
Renault Sefrane 2000cc 16V
Renault Laguna 2000cc 8v
Renault Laguna 2000cc 16v
Renault Espace 2000cc 8v
Renault SAGEM SAFIR 1 and 2
Renault Clio 1200cc 8V
Renault Clio 1400cc 8V
Renault Clio 1600cc 8V
Renault Clio 2000cc 16V Williams
Renault Laguna 1800cc 8V
Renault Laguna 2000cc 8V
Renault Laguna 1800cc 16V
Renault Laguna 2000cc 16V
Renault Twingo 1200cc 8V
NOTE: If reset pin is connected to ground then it must be lifted or the track cut before decoding. This can be re-attached after decoding the ecu.
As a rule of thumb keep the power connected to the ECU for a futher five minutes after the decoder has completed the decoding process.
Sagem SL96 Psa
Peugeot 306 1400cc 8V
Peugeot 306 1600cc 16V
Peugeot 306 1800 16V
Peugeot Ranch 1400 8V
Citroen Berlingo 1400cc 8V
Citroen Xrara 1400cc 8V
Citroen Xrara 1800cc 16V
DAEWOO SIEMENS
Daewoo Matiz 800cc
HYUNDAI SIEMENS
Hyundai Coupe 1600cc 16V
Hyundai Coupe 2000cc 16V
KIA SIEMENS
Kia Rio 1300 16V
Kia Rio 1500 16V
MAGNETI MARELLI
1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90,
Citroen Berlingo 1800cc 8V
Citroen Saxo 1400cc 8V
Citroen Saxo 1600cc 16V
Citroen Xara 1400cc 8V
Citroen Xara 1800cc 8V
Citroen Xara 2000cc 16V
Citroen ZX 1400cc 8V
Peugeot 106 1400cc 8V
Peugeot 106 1600cc 8V
Peugeot 106 1600cc 16V
Peugeot 206 1100cc 8V
Peugeot 206 1400cc 8V
Peugeot 306 1400cc 8V
Peugeot 306 1600cc 8V
Peugeot 306 1800cc 8V
Peugeot 405 1800cc 8V
Peugeot 406 1800cc 8V
Peugeot Partner 1800 8V
TMS-374
1AP\SAGEM\SIEMENS

Berminat Hubungi   :
Nama : Agus yulianto    
Alamat : Puri Astapada Indah 2 Blok K/6 RT/RW 03/08 Plosogeneng
          Jombang, 61416 Jawa Timur
Telp : Simp. 081332787811

Web  :
www.obd2jatim.com


Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Tools

Super TOYOTA K+CAN commander 2.0

Toyota Key Programer Super Toyota K dan CAN 2.0 Commander 2.0 

Product Name :  Super TOYOTA K+CAN commander 2.0

Part No :  Super TOYOTA K+CAN commander 2.0

Connecting with all electronic control modules in the vehicle. Working by K and CAN bus diagnostic connection.

Function :
• For all electronic control units read
• Clear Error DTC
• Clear Memories Pending
• Read Standart,
• Read history memory.
• Actuator test
• Current data.
• Keyprogramming - normal and
• Keyprogramming smart key for vehicles
• Etc

Super Toyota K + BISA 2.0 Komandan 2.0 Key Programmer USB

Nama Produk: Super TOYOTA K + BISA komandan 2.0
Tidak ada bagian: Super TOYOTA K + BISA komandan 2.0

Menghubungkan dengan semua modul kontrol elektronik di dalam kendaraan. Bekerja dengan K dan CAN BUS koneksi diagnostik.

fungsi
• Untuk semua unit kontrol elektronik baca
• Hapus Kesalahan DTC
• Hapus Kenangan Tertunda
• Baca Standart,
• Baca memori sejarah.
• Tes Actuator
• Data saat ini.
• Keyprogramming  Immo

• Keyprogramming Smart Key
• Dll

Special Function :
Connect with some control module.
Select vehilcle model and scan modules.
Choose some special function - Immo reset and key programming.
Specification:
Key programming - normal and smart key for vehicles

Package List:
• 1 K+Can Main Unit
• 1CD


Car Maker :
• Toyota Rav4
• Toyota Yaris (smart key)
• Toyota Auris (smart key)
• Toyota Land Cruiser 100
• Toyota Land Cruiser 120
• Toyota Prado
• Toyota 4 Runner
• Toyota Camry (2004+)
• Toyota Corolla (2007+)
• Toyota Prado
• Toyota Hilux
• Toyota Prius
• Toyota Avalon
• Lexus LX470
• Lexus LX570
• Lexus RX300
• Lexus RX330
• Lexus RX350
• Lexus RX400
• Lexus RX400h
• Lexus SC430
• Lexus GS300
• Lexus GS430
• Lexus GS450
• Lexus ES350
• Lexus IS220
• Lexus IS250
• Lexus IS350
• Lexus LS430
• Lexus LS460
• Scion

Berminat Hubungi  :
Nama : Agus yulianto    
Alamat        : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
                                  Plosogeneng Jombang, 61416 Jawa Timur
Telp : 081332787811  

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Scanner

Wireless Super VCS Car Diagnostic Tool Universal vcs plus vdm

Wireless Super VCS Car Diagnostic Tool Universal Diagnostic Tool Super VCS Wireless Automotive Diagnostic Tool

Rp 2.500.000

Super VCS Wireless Compact  Diagnostic tool, VCS dan VDM VCS+VDM  2 in 1

2.500.000

Specifications
MCU:  ARM7 processor, 66MHz
Input Voltage:  DC 8-18V
Communication Mode:  USB and Wifi
Storage Temperature:  -30 to 120 C(-22 to 248 F), Relative Humidity: <90%
Operating Temperature:  -30 to 120 C(-22 to 248 F), Relative Humidity: <90%

Scanner  Super VCS , Diagnostic tool VCS+VDM 2 in 1 Super
1. Merupakan kombinasi dari Scanner dan Scanner VDM,
2. Fungsi hampir sama dengan VCS ataupun VDM.
3. Bahasa: Inggris
4. WIFI dan USB Connection: The WIFI jarak langsung kurang lebih 50m
5. Basic win 32 Bit xp dan win 7
6. Langsung digunakan Tidak perlu aktivasi
7. atau Pendaftaran sebelum menggunakan.
8. Fungsi dikenal sangat stabil.
9. vcs super Meliputi 44 Merek Mobil:

Mobil Eropa Model :
Audi, Benz, BMW, Citroen, Fiat, Ford Uni Eropa, Jaguar, Lancia, LandRover, MINI, Opel, Peugeot, Porsche, Renault, Saab, Seat, Skoda, Smart, Vauxhall, Volvo, VW.

Asia Mobil Model :
Acura, Honda, Hyundai, Infiniti, Isuzu, Kia, Lexus, Mazda, Mitsubishi, Nissan, Perodua, Proton, Subaru, Suzuki, Toyota

Mobil Australia Model : Ford AU, Holden

Amerika Model :
Chrysler, Ford, GM.

Mobil China Model :
Chery, Geely, GWM


Super VCS Introduction
The Super VCS Compact Diagnostic Partner is the combanation of vcs and vdm. It is ingeniously designed to recreate the functionality of the OEM tools used by automotive manufacturers’ dealers, empowering independent garage shops to provide complete servicing in their own shops, including data stream, reading and clearing of diagnostic trouble codes, and immobilizer key coding, etc.

Super VCS Fungsi diantaranya :
• Quick Test,
• Read Ecu Info.
• Read Dtcs,
• Erase Dtcs,
• Clear Learning Value,
• Data Stream,
• Actuations,
• Read Freeze Frame Data,
• Read/Write Vin,
• Basic Reset,
• Control Unit Adaptations,
• Throttle Adaptations,
• Air Bleeding,
• Level Calibration,
• Theft Alarm Reset,
• Key Programming,
• Immobilizer Coding
• Component Activation
• Oil Change,
• Idle Speed Learning,
• Idle Speed Adjustment,
• Ignition Timing Adjustment,
• Camshaft Timing Control Learning,
• Maintenance Functions,
• Boot Mode
• ECU Initial startup,
• ECU initialization

• Super VCS Supported Systems:
ME-Motor electronics,
• CDI-Common Rail Diesel Injection,
• ETC-Electronic transmission control,
• ESM-Electronic selector module,
• SBC-Sensotronic Brake Control,
• ESP-Electronic stability program,
• BAS-Brake assist, Suspension,
• TPC-Tire pressure monitor,
• Airbag,
• CGW-Central gateway,
• EIS-Electronic ignition switch,
• OCP-Overhead control panel,
• UCP-Upper control panel,
• XALWA-Xenon headlamp,
• HRA-Headlamp range control,
• ATA-Anti-theft alarm system,
• IC-Instrument cluster,
• ASSYST-Active Service System,
• SCM-Steering column module,
• EPS-Electrical power steering,
• PTS-Parktronic system,
• EPB-Electric parking brake,
• COMAND/AUDIO, CD/DVD,
• TV tuner,
• CTEL-Cellular telephone,
• DCM-Door control module,
• ESA driver-Electric seat adjustment driver,
• ESA passenger-Electric seat adjustment passenger,
• AAC-Air conditioning,
• WSS-Weight sensor system,
• SVMCM-Special vehicle multifunction control module.
• Can check out the year and model of the vehicles automatically and quickly.


Super VCS Features
Supporting ISO 9141-2,
K/L line,
SAE-J1850 VPW,
 SAE-J1850 PWM,
CAN ISO 11898,
ISO15765-4 protocols.
High-speed,
medium speed and low speed CAN-BUS,
Single CAN-BUS diagnosis protocols is supported.

Spesifikasi
• MCU: prosesor ARM7, 66MHz
• Input Voltage: DC 8-18V
• Komunikasi Mode: USB dan Wifi
• Suhu Penyimpanan: -30 sampai 120 C (-22 ke 248 F), Kelembaban Relatif: <90%
• Suhu operasi: -30 sampai 120 C (-22 ke 248 F), Kelembaban Relatif: <90%


Super VCS Daftar Paket :
• 1pc x Unit super VCS utama dengan kabel OBDII
• 1pc x USB Kabel
• 1pc x Software CD
• 1pc kotak x karton


Berminat Hubungi  :
Nama  : Agus yulianto    
Alamat  : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
              Plosogeneng Jombang, 61416 Jawa Timur
Telp          : 081332787811  

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Scanner,Tools

BMW Reset/Inspection Airbag Oil

BMW  Reset/Inspection  Airbag Oil

Reset Inspection and Oil Service
16 pin male connnector
Suitable for over 75 different BMW and MINI models with OBD2 diagnostic socket from build 2000, such as BMW E39,E46, E50, E52, E53, Mini ,E38, X5, Z4

Main Features:

Plug the device into the OBD2 socket of your car;
All LEDs will flash and then stay on;
Turn ignition key to enable the board electronic but don't turn on the motor;
Press the button for the operation you want to perform;
The LED of the choosen operation will turn on and the other LEDs will be off;
LEDs will perform a light chain which means reset is done.

Package include:
 1 X Reset Tool for BMW


Berminat Hubungi  :
Nama : Agus yulianto      
Alamat         : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
                                  Plosogeneng Jombang, 61416 Jawa Timur
Telp : 081332787811    

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Scanner,Tools

Willem EPROM Programmer PCB5.5M

Willem EPROM Programmer PCB 5.5M

Features and Advantages
Dapat memprogram EPROM, EEPROM, FLASH, Serial EPROM, Serial Flash Dan lain-lain Tegangan  (Vpp 3.6V, 12.5V, 21V, 25V)

Versi hardware adalah  PCB50 dan mendukung perangkat 3V3-3V6 SPI Flash. * Chip SPI , Hal ini dapat memprogram hingga 10% lebih cepat dari Willem PCB4.5C, 20% lebih cepat dari Willem EPROM Programmer (PCB3.5C) / (PCB4C) dan 50% lebih cepat dari PCB3B yang +,  Menggunakan catu daya dari port USB


Mengapa Alat ini sangat dibutuhkan ?? mengingat kegunaanya diantaranya :
• Refreshing, Upgrading, Programming BIOS chips.
• Motor Vehicle memory device, MEMCAL or ECU code reading, writing.
• Copier, Fax machine, Printer main board maintaining or repairing.
• VCD, DVD, Color TV maintaining or repairing.
• Neon Light Controller code writing.
• MCU development - programming for MCS-51 series, AVR series and PIC series MCU.
• Repairing, reading, writing, programming PC motherboard BIOS Chips.
• Upgrade the chip in your cars computer.
• Modify the chips in your Xbox or PlayStation Console.
• Programming MicroChip PIC Micros.
• Programming ATMEL AVR Micros.
• Flash a 3V6 SPI device on your motherboard or HDD.
• Refreshing, Upgrade, chip BIOS Programming.


All Software is included on CD
Software Version 0.98D12 - for PCB5.0 is now released.
Software Version 0.98D10 - for PCB5.0 is now released.
Software Version 0.98d9 - for PCB5.0, in stable beta now - adds support for 3V6 SPI Flash devices and includes many improvements.*
Software Version 0.98d6 - update June 2006 (will work with PCB4.5C - not for PCB5.0)
Software Version 0.98d5 - update September 2005 (called PCB45-0.98D5 - for use with the PCB5.0)
Software Version 0.98d4 - update August 2005
Software Version 0.98d3 - more support for PIC micro's
Software Version 0.98d2 - further support for 3.5/3.7/4c
Software Version 0.98d1 - stability and support for 3.5/3.7/4c
Software Version 0.98d - some fixes for XP
Software Version 0.98c - adds lots of support for PIC micro's.
Software Version 0.98a ( 0.98a [alpha] )
Software Version (0.98ap) *** CAN UNLOCK AM29F040B ***
NEW SPI FLASH DEVICES SUPPORTED
WINBOND
W25X010,W25X020,W25X040,W25X080,W25X16,W25X32,W25X64

MXIC
MX25L512,MX25L1005,MX25L2005,MX25L4005A,MX25L8005A,MX25L1605,MX25L3205
MX25L6405

EON
EN25B05 , EN25B10 , EN25B20 , EN25B40 , EN25B80 , EN25B16 , EN25B32 , EN25B64EN25P05 , EN25P10 , EN25P20 , EN25P40 , EN25BP80 , EN25P16 , EN25P32 , EN25P64, EN25D80 , EN25D16 , EN25F20 , EN25F40 , EN25F80 , EN25F16

AMIC
A25L05P-B,A25L10P-B,A25L20P-B,A25L05P-T,A25L10P-T,A25L20P-T,A25L512
A25L010,A25L020,A25L040,A25L080;,A25L016,A25L032

pFLASH
Pm25LV512,Pm25LV010,Pm25LV020,Pm25LV040,Pm25LV080,Pm25LV016

Numonyx (ST)
M25P05,M25P10,M25P20,M25P40,M25P80,M25P16,M25P32,M25P64
M25PE10,M25PE20,M25PE40,M25PE80,, M25PX80,M25PX16,M25PX32,M25PX64

SPANSION
S25FL004A/040A,S25FL008A,S25FL040A-T,S25FL040A-B,S25FL016A,S25FL032A
S25FL064A

ATMEL
AT25DF021,AT25DF041A,AT25DF081,AT25DF081A,AT25DF161,AT25DF321A
AT25DF641,AT26DF041,AT26DF161A,AT26DF321


other Willem EPROM Programmer can support CHIPS(EPROM,EEPROM,FLASH,I2C,PIC,MCS-51,AVR, 93Cxx, ISP)

EPROM
27C64 , 27C128 , 27C256 , 27C512 , 27C010 , 27C020 , 27C
040 , 27C1001, M27C1001 , M27C2001 , M27C4001, 27C080 (A19) , M27C801 , M87C257, 2716(Vpp25V) , 2732 , (adapter DIP24), 2764 , 27128 , 27256 , 27512 , 27010,  Vpp12.5V (21Vpp Modify Circuit

EEPROM


28C65 , 28C64 , 28C128 , 28C256 , 28C512 , 28C010 , 28C020 , 28C040
M28C16A/17A (DIP28), (Adapter or Jumper) 28C16,XLS2816 (DIP24)

FLASH Memory
28F64 , 28F128 , 28F256 , 28F512 , 28F010 , 28F020, MX26C1000 , MX26C2000 , MX28F1000 , MX28F2000, Am28F256A , Am28F512A , Am28F010A , Am28F020A
New command erase/prog.)-- intel ---

FLASH Memory
i28F001BX , 28F004 , 28F008 , 28F016, 29F64 , 29F128 ,29F256 , 29F512 , 29F010 , 29F020 , 29F040 , 29F080, 29F001 , 29F002 , 29F004 , 29F008 , 29F016 , 29F032 , V29C51002T , 29LV040

Serial (I2C) EEPROM
24Cxx, 24C02 , 24C04 , 24C08 , 24C16 , 85C72 , 85C82 , 85C92
24C32 , 24C64 , 24C128 , 24C256 , 24C512

Microwire EEPROM
<------ Data 8bit ----->(pin 6 ->ORG. [Schematic connect to GND]), 93C06 , 93C46 , 93LC46 , 93C56 , 93C57, 93C66 , 93C76 , 93C86 (8bit) , AT59C11 , AT59C22 , AT59C13, CAT35C102 , CAT35C104 , CAT35C108 (pullup pin7)
<------Data 16bit------> (pin 6 ->NC [No Connect]), 93C06A , 93C46X , 93C56 , 93C66 , 93C76 , 93C86 (NS)

Microchip PIC
16C84 , 16F84 ,16F84A , 16F627/16F628, 12C508/A , 12C509/A , 12CE518 , 12CE519 , 16C505, 16C620 , 16C621 , 16C622 , 16CE623 , 16CE624 , 16CE625 , 16C710/711
---ICSP connector----, 16F870 , 16F871 , 16F872 , 16F873 , 16F874 , 16F876 , 16F877 PIC16F873A , PIC16F874A , PIC16F876A , PIC16F877A, -Add PIC microchip 14bit, PIC12F629 , PIC12F675 , PIC16F630 , PIC16F676 , PIC12F635 , PIC12F683 , PIC16F636 , PIC16F684 , PIC16F688, PIC16F72/73/74/76/77 , PIC16F737/747/767/777 , PIC16F87/88 , rfPIC12F675x , PIC16F785/PS200 , PIC16F716, -Add microchip 14bit,12bit OTP PIC12C671 , PIC12C672 , PIC12CE673 , PIC12CE674, PIC16C61/71 , PIC16C62/64/65/73 ,, PIC16C62A/62B/62C/63/63A/64A/65A/65B/66/67, PIC16C72/72A/73A/74A/74B/76/77 , PIC16C620/620A/621/621A/622/622A, PIC16CE/623/624/625 ,, PIC16C710/711/712/716 , PIC16C773/774 , PIC16C745/765/923/924 , PIC16C925/926, PIC16C554/556/557/558 , PIC16C432/433 , PIC16C717/770/771/781/782, -Additional PIC microchip 14bit
PIC12F629/675 , PIC16F630/676 , PIC12F635/683 , PIC16F636/684/688 ,, PIC16F72/73/74/76/77 ,, PIC16F737/747/767/777 , PIC16F87/88 , rfPIC12F675x , PIC16F785/PS200 , PIC16F716, -Additional microchip 14bit OTP., PIC12C671 , PIC12C672 , PIC12CE673 , PIC12CE674 , PIC16C61/71 ,,PIC16C62/64/65/73 , PIC16C62A/62B/62C/63/63A/64A/65A/65B/66/67 , PIC16C72/72A/73A/74A/74B/76/77 ,PIC16C620/620A/621/621A/622/622A , PIC16CE/623/624/625 , PIC16C710/711/712/716 , PIC16C773/774 , PIC16C745/765/923/924 , PIC16C925/926 , PIC16C554/556/557/558 , PIC16C432/433 ,
PIC16C717/770/771/781/782
-Additional PIC microchip 12bit (FLASH memory)
PIC12F508/509 , PIC10F200/202/204/206 , PIC16F505 , PIC16F54/57, -Add PIC18Fxxx
PIC18F242 , 18F248 , 18F252 , 18F258 , 18F442 , 18F448 , 16F452 , 16F458,PIC18F1220 , 18F2220 , 18F4220 , 18F1320 , 18F2320 , 18F4320, PIC18F6520 , 18F6620 , 18F6720 , 18F8520 , 18F8620 , 18F8720, PIC18F2331 , 18F2431 , 18F4331 , 18F4431
PIC18F6525 , 18F6621 , 18F8525 , 18F8621
PIC18F6585 , 18F6680 , 18F8585 , 18F8680
PIC18F2439 , 18F2539 , 18F4439 , 18F4539
PIC18F6410 , 18F8410 , 18F6490 , 18F8490
-Additional PIC18Fxxx
PIC18F2410 , PIC18F2420 , PIC18F2455
PIC18F2510 , PIC18F2515 , PIC18F2520 , PIC18F2525 , PIC18F2550 , PIC18F2585
PIC18F2610 , PIC18F2620 , PIC18F2680
PIC18F4410, PIC18F4420 , PIC18F4455
PIC18F4510 , PIC18F4515 , PIC18F4520 , PIC18F4525 , PIC18F4550 , PIC18F4585
PIC18F4610 , PIC18F4620 , PIC18F4680
-Additional Find and edit value OSCCAL (PIC12F629/675 , PIC16F630/676)
-Additional Edit config at address 0x2008,0x2009 (PIC12F635/683 ,
PIC16F636/684/688 , PIC16F785)
Fixed Programming PIC all
Test on chip
PIC12F675 , PIC16F676 , PIC16F684 ,PIC16F767, PIC16F74
PIC16F872 , PIC16F876 , PIC16F877, PIC16F876A, PIC16F873A, PIC16F819
PIC16F84 , PIC16F84A , PIC16F628, PIC16F628A,
epromPIC12C509JW , PIC16C505JW , PIC16C711JW , PIC16CE625JW

Microchip PIC
PIC18F458 , PIC18F4320 , PIC18LF258 , PIC18F4539 , PIC18F4431

Atmel Flash Memory
AT49Fxxx (Subset 29Fxxx)
(Byte-by-Byte Programming)
(Software Data Protection)

Command seq. 5555/AA, 2AAA/55, 5555/A0
AT49F512 , AT49F010 , AT49F020 , AT49F040
SST39SF010 , SST3S9F020 ,SST39SF040
AT49F001 , AT49F002 , AT49F008A

Command seq. 555/AA, 2AA/55, 555/A0
Am29F512 , Am29F010 , Am29F020 , Am29F040 , HY29F080
29F002 , 29F002T , Pm29F002T

Atmel Flash Memory, (Sector Programming).,(Software Data Protection)

AT29C256 , AT29C512 , AT29C010A , AT29C020 , AT29C040 , AT29C040A, W29EE512 , W29EE011 , W29EE012 , W29C020(128) , W29C040, PH29EE010(W29EE011), ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020), Ver 0.992 up(DOS). Can run under win9x, (disable prog. CPUIdle or CPUCool), AT49BV512


Serial Peripheral Interface (SPI), EEPROM Mode0 (0,0), AT25xxx, W95xxx
[Atmel] AT25010 , 020 , 040 (A8-A0), AT25080 , 160 , 320 , 640 , 128 , 256 (A15-A0)
[ST] W95010....256, Microchip 25x010 - 25x640
--- Byte programming
25010 , 25020 , 25040
--- Page programming
25C080 , 25C160 , 25C320 , 25C640 , 25C128 , 25C256 , 25C512
AT25HP256 , AT25HP512 , M25P10 , M25P20 , M25P40
AT25HP1024 (24bit address)
-- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx
CAT64LC010, CAT64LC020, CAT64LC040

Atmel EEPROM(page prog.)(Software Data Protection)
AT28C256 , AT28C010 , AT28C040

Nonvaltile SRAM (DS12xx)
DS1220 , DS1225Y , DS1230Y/AB , DS1245Y/AB , DS1249Y/AB

static RAM (Test RAM)
6116 , 6264 , 62256 , 62512 , 628128

EPROM winbond,SST
Electrical Erase Chip
W27E512 , W27E010 , W27C010 , W27C020 , W27C040
SST27SF256 , SST27SF512 , SST27SF010 , SST27SF020
MX26C4000
Vcc = 3.3-3.6V SST37VF512 , SST37VF010 , SST37VF020 , SST37VF040

Flash Memory SST,Sanyo
SST28SF040A , LE28F4001

ackage including :
+ A BRAND NEW Willem Eprom Programmer PCB5.0
+ A USB Cable to connect to your PC
+ A Parallel Port Cable to connect the programmer to your PC
+ A CD containing all the software

Berminat Hubungi  :
Nama  : Agus yulianto    
Alamat  : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
     Plosogeneng Jombang, 61416 Jawa Timur
Telp  : 081332787811  

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI



rp 850.000

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Tools

Automotive Signal Sensors Tester ECU

Automotive Signal Sensors Tester ECU 

Product Description
Untuk memperbaiki mobil kkhususnya mobil-mobil masa kini, yang bisa di bilang sudah basic komputernisasi ni diperlukan alat yang memadai untuk menentukan permasalahan atau kerusakan di mobil, salah satunya yaitu scanner disamping itu ada alat yang tidak kalah pentingnya yang dinamakan atau dikenal dengan nama : “Sensor Simulator of Signals “

Item specifics
Item Width  : 11 cm
Item Weight : 780 g
External Testing Certification     : CE
Item Length :16 cm
Item Height : 4 cm
Model Name : 6300B
Car Maker : Universal
Special Features : Sensor Simulator
Package Size         : 28cm x 18cm x 12cm (11.02in x 7.09in x 4.72in)

Fungsi Sensor Simulator of Signals diataranya adalah:

Memeriksa atau Mengukur Sinyal Otomotif Sensor diantaranya :
Diagnostic semua sensor
Kabel sensor/wiring
Conector
Tegangan
Lamda
Frekuensi
Pulsa
Output aktuator
Input aktuator/sensor
Tegangan AC
Tegangan DC
Simulasi Sensor
Komponen Manajemen Komputer
Simulating sensor suhu,
throttle potentiometers,
Simulating switches,
Simulating air flow meters
Simulating lambda/oxygen sensors
Cheek Basic ECU Operation
Simulates actual working Aircondition of any sensor without having to remove it from the
Simulates actual working  vehicle A.B.S.,
Simulates actual working  Crank,
Simulates actual working  Can, Coolant, Oxygen,
Simulates actual working  MAP
Simulates actual working MAF,
Simulates actual working MAT,
Simulates actual working VSS,
Cheek Basic ECU Operation
etc.



Berminat Hubungi  :
Nama : Agus yulianto    
Alamat : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
                   Plosogeneng Jombang, 61416 Jawa Timur
Telp : 081332787811  

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Artikel Umum,Tools

Auto Automotive Sensor Simulator of Signals Tester ECU Operation testing

Auto Automotive Sensor Simulator of Signals Tester ECU Operation testing

Product Description
Untuk memperbaiki mobil kkhususnya mobil-mobil masa kini, yang bisa di bilang sudah basic komputernisasi ni diperlukan alat yang memadai untuk menentukan permasalahan atau kerusakan di mobil, salah satunya yaitu scanner disamping itu ada alat yang tidak kalah pentingnya yang dinamakan atau dikenal dengan nama : “Sensor Simulator of Signals “

Fungsi Sensor Simulator of Signals diataranya adalah:

Memeriksa atau Mengukur Sinyal Otomotif Sensor diantaranya :
Diagnostic semua sensor
Kabel sensor/wiring
Conector
Tegangan
Lamda
Frekuensi
Pulsa
Output aktuator
Input aktuator/sensor
Tegangan AC
Tegangan DC
Simulasi Sensor
Komponen Manajemen Komputer
Simulating sensor suhu,
throttle potentiometers,
Simulating switches,
Simulating air flow meters
Simulating lambda/oxygen sensors
Cheek Basic ECU Operation
Simulates actual working Aircondition of any sensor without having to remove it from the
Simulates actual working  vehicle A.B.S.,
Simulates actual working  Crank,
Simulates actual working  Can, Coolant, Oxygen,
Simulates actual working  MAP
Simulates actual working MAF,
Simulates actual working MAT,
Simulates actual working VSS,
Cheek Basic ECU Operation
etc.


Item specifics
Item Width : 11 cm
Item Weight : 780 g
External Testing Certification     : CE
Item Length :16 cm
Item Height : 4 cm
Model Name : 6300B
Car Maker : Universal
Special Features : Sensor Simulator
Package Size        : 28cm x 18cm x 12cm (11.02in x 7.09in x 4.72in)

Berminat Hubungi  :
Nama : Agus yulianto      
Alamat : Perum Puri Astapada Indah 2 Blok K/6 RT/RW 03/08
                   Plosogeneng Jombang, 61416 Jawa Timur
Telp : 081332787811    

Web  :
www.obd2jatim.com

Blog  :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyulianto2.blogspot.com

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99

Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI

Read more »

Posted in: Artikel Otomotif,Tools

KESS V2 OBD2 Tuning Kit KESS ECU Programmer V2.23 Hardware V4.036

KESS V2 OBD2 Tuning Kit KESS ECU Programmer V2.23 Hardware V4.036 

Fitur  Kess V2 termasuk:

1. Check of the battery voltage in real-time
2. Full Recovery function in case of problems
3. Automatic correction of the Checksum, (where available)
4. Boot-Loader mode supported
5. Management of the programming counters
6. ScanTool function to remove DTC
7. Several options of reading/writing speed
8. Option to write full file/section of the map
9. Full integration with ECM Titanium,which means it can work with ECM Titanium perfectly
Dengan cakupan dari semua merek utama dan protokol termasuk Line, CAN, EDC17 dan MED17 dan Ford J1850. Kess V2 adalah semua yang Anda butuhkan untuk bekerja sebagai tuner dan teknisi  harga yang sangat terjangkau.


KESS V2 OBD2 Tuning Kit KESS ECU Programmer V2.23 Hardware V4.036
No Token Limitation Update by CD


Top 6 Reasons To Get KESS V2
1. Firmware V4.036
2. Software Version: V2.23
3. Update by CD
4. No Token Limitation: can be used unlimitedly, no need to worry about tokens any more.
5. With Coverage of All Major Brands and Protocols including Line, CAN, EDC17 and MED17 and Ford J1850
6. Supported Languages: English, German, Spanish, Italian, Portuguese, French


KESS V2 OBD2 Manager Tuning Kit without Tokens Limitation
Kess V2 has several built in features and safeguards including:
1. Check of the battery voltage in real-time
2. Full Recovery function in case of problems
3. Automatic correction of the Checksum, (where available)
4 Boot-Loader mode supported
5. Management of the programming counters
6. ScanTool function to remove DTC
7. Several options of reading/writing speed
8. Option to write full file/section of the map
9. Full integration with ECM Titanium,which means it can work with ECM Titanium perfectly


Notice:
1.Do remember disconnect internet.(When you using this version KESS V2, please make sure your computer do not have internet. This is very important, connect to internet may damage the hardware and can not repair by your side, you must send back to us for repair.)
2.Do connect with your car when you install the software.(Otherwise software can't be installed successfully)
3. If you want to update hardware of your old KESS V2, will have to ship back the multiplexer
4. Support System: Windows XP
With coverage of all major brands and protocols including Line, CAN, EDC17 and MED17 and for Ford J1850Kess V2 is everything you need to work as a successful tuner at a very affordable price.


KESS V2 OBD2 Manager Tuning Kit without Token Limitation

Fitur  Kess V2 termasuk:

1. Check of the battery voltage in real-time
2. Full Recovery function in case of problems
3. Automatic correction of the Checksum, (where available)
4. Boot-Loader mode supported
5. Management of the programming counters
6. ScanTool function to remove DTC
7. Several options of reading/writing speed
8. Option to write full file/section of the map
9. Full integration with ECM Titanium,which means it can work with ECM Titanium perfectly

Dengan cakupan dari semua merek utama dan protokol termasuk Line, CAN, EDC17 dan MED17 dan Ford J1850. Kess V2 adalah semua yang Anda butuhkan untuk bekerja sebagai tuner dan teknisi  harga yang sangat terjangkau.


6 Alasan Utama Memilih  Kess V2 V2.23 Hardware V4.036

1. Master Versi
2. Software Versi: V2.23 Hardware V4.036

Perhatikan:
1. Jangan memperbarui alat ini secara online,
2. Jangan On line Pada waktu menggunkan
3. Mudah Tidak menggunakan  Token Batasan,
4. Kess V2 memiliki 60 Tokens, ketika Anda menggunakannya, Anda dapat menggunakan JLink Ditambah Kess V2 Chip CPU untuk Perbaikan untuk memprogram ulang dan mendapatkan selain 60 Tokens
5. Jika  v2.1.0 dianti versi lama sebaiknya seperti V2.06 penuh atau V1.89, Anda perlu menggunakan JLink Ditambah Kess V2 Chip CPU Perbaikan untuk reflash CPU Anda dan TF Card, atau dengan menggunakan komputer lain untuk menginstal perangkat lunak versi lama


Agus Yulianto
Perum Puri Astapada Indah 2 Blok K No:6 Plosogeneng
Kec .Jombang, Kab.Jombang, Jawa Timur 61416 Indonesia

Alamat Lokasi toko/rumah Google map
https://goo.gl/maps/7NZ4HMSYvvJ2

Hp.  0813-3278-7811 0857-4623-3838 Kantor  0321-852845

Web  :
www.obd2jatim.com

Blog  :
http://agusyulianto2.blogspot.com
http://obd2murah.blogspot.com
http://Toolsteknik.blogspot.com

Tokopedia
https://www.tokopedia.com/obd2

Bukalapak
https://www.bukalapak.com/agusyulianto

Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99


Rp 2..500.000,-

Read more »

Posted in: Tools

Smart Key Immo For Toyota Smart Keymaker OBD for 4D chip

Smart Key Immo  For Toyota Smart Keymaker OBD for 4D chip

(Support for Toyota Lexus Smart Key)

Smart Key Immo  For Toyota Smart Keymaker OBD for 4D chip

(Support for Toyota Lexus Smart Key)

Security and high efficiency: It's only need almost 20 seconds to finish one key making. It can be used securely for all the 4D and smart keys anti-theft system of Toyota series without the dangerous to destory the anti-theft system. This product is the fastest and safest instrument to do the key programming of Toyota and Lexus series in case of all keys losing.

The detailed operating steps are as following:

Common Keys

1.Turn the ignition switch "ON" using the key with the orginal 4D chip.

2. Insert the key programmer to the car diagnostic interface OBD, and the instrument will enter into the procedure of car auto searching with a short sound of "di". 7 seconds later, the key programmer connect with the car computer successfully with the short sound of two or three "di"(two means the car is belong to the second generation and the three means third generation.); After 20 seconds, the instrument will enter into the "learning key procedure" with a long sound of "di".

3. Reading the key code

3.1.Match two main keys and one subsidiary key to the IMMO computer(attention: There must be two new main keys and one subsidiary key)

a)  Insert the first new key into the ignition lock and wait for 5 seconds,and then the SEC light turns on.(Don't turn on the ingntion when the key is inserted.)

b) Insert another main key into the ignition lock and wait for 5 seconds, and then the SEC light turns on.(Don't turn on the ingntion when the key is inserted.)

c) Insert the subsidiary key into the ignition lock and then the SEC light turns off. (Don't turn on the ingntion when the key is inserted.)

3.2.Only match one or two main keys to the immo computer ( Close the matching mode manually after the matching finished.)

a) Insert the first main key and wait for 5 seconds, SEC light turns on. (Don't turn on the ingntion when the key is inserted.)

b)Insert the second main key and wait for 5 seconds, SEC light turns on. (Don't turn on the ingntion when the key is inserted.)

c)Insert the first finished key, turn on the ignition quickly for 5 times and then take out.

Smart Keys

1.Safe and efficient: Only need 20 seconds to add one key

2.It is safe for the  security alarm system

3.Support all kinds of Toyota and Lexus smart key system: support K line and CAN-BUS protocols

4.It is the most safe and fast key programmer device for Toyota and Lexus series till now.

5.It supports all key lost

Using the smart key

1. Add the other keys into the main key

1.1..Insert the key programmer to the car diagnostic interface OBD, and the instrument will enter into the procedure of car auto searching with a short sound of "di".

1.2.Push the start-button twice. After 7 seconds the vehicle will connect the devices successfully, and the equipment will send off a sound of "di" with 4-5 times, (4 sounds mean that the system is the 4th period, 5 sounds mean that the system is the 5th period); after waiting for 30 seconds the equipment will send off a long soung of"di", it means the car enter into "learning key state."

2. When lost all keys or only have the deputy key, we need to do it initialize:

2.1.Hold down the LED button on the equipment, and insert it into the OBD, and release the button after the sound of "di" twice,the device enter into the state of search vehicles in this time. :

2.2..Push the start-button twice. After 7 seconds the vehicle will connect the devices successfully, and the equipment will send off a sound of "di" with 4-5 times, (4 sounds mean that the system is the 4th period, 5 sounds mean that the system is the 5th period); after 5 seconds the lights of SEC will be off; after waiting for 10-16 minutes the equipment will send off a long sound of "di", and the SEC lights flashing, that means the car enter into "learning key state."

3. Learning the intelligent key to the anti-theft of computer:

When the sign back of the intelligent keys near the button, will hear 2 sounds of "di" "di" at this time, the SEC lights will flash twice;after learning all the intelligent keys, it have to wait for 30 seconds until the SEC lights flash,and the system will close the learning pattern automatic.

Notice:

1.Must use the right new smart keymaker, and follow the right step above, otherwise you take the consequences.

2.If the device can match the key, and LED light shining constantly, pls clear the error code by using anti-theft system

3.After finishing program keys, the key can strat but the SEC light is still turn on, maybe you use the vice key, only main key can manually shut the study mode.

4. Dont try to open the cover of programmer and dash board, otherwise you take the consequences.

5..This machine is only provided for the legal auto repair. Otherwise you will take the above consequences

Read more »

Posted in: Artikel Otomotif,Artikel Umum