17.05
obd2jombang
CR1000
High
pressure common rail injector tester user manual
l Chinese，English, optional
l Support magnetic
and piezo injectors（BOSCH, DENSO,DELPHI）；
l Support piezo
injectors（BOSCH,SIEMENS）
l Support
Caterpillar injector（C7,C9）
l Support VE test；
l Overcurrent and short
circuit protection
l Support magnetic
injector impedance measurement;
l Record number of
users
l Customizable
boot LOGO;
Table of
Contents
1 Outline
1.1
Brief introduction
1.2 About
Security
1、in the course of operating the tester, the operator should
wear safety glasses;
2、using a separate dedicated outlet and reliable grounding.
The tester is a three-wire power cord plug is connected to a standard
three-wire outlet, please ensure reliable grounding;
3、if the power supply voltage is unstable, please connect the
power supply voltage tester uses;
4、regularly check the AC power cord is damaged, and the power
plug or power outlet for dust accumulation;
5、if the tester abnormal conditions occur, or an abnormal
sound or smell, or the tester can not be hot to the touch, stop using it
immediately and unplug the AC power outlet power cord and all other cables;
6、if the tester fails, please contact the service personnel to
obtain necessary assistance;
1.3 Use and maintenance
1、Do not throw, drop or step on the tester, the tester to
avoid being a strong external impact;
2、Do not insert foreign objects into the connector portion
tester;
3、Do not allow water or other liquids to flow into the
interior or on the tester tester;
4,、do not touch with wet hands AC power cord terminals;
5,、do not let dust or foreign matter on the terminals around
the AC power, the AC terminals on the accumulation of dust and foreign matter
may cause a fire or electric shock;
6、avoid stepping on or pinched AC power cord;
7、unplug the power cord when cleaning the tester.
2
Accessories
and Interface Description
2.1
Check the accessories
After receiving the goods,
please open the box and check box items are consistent with the packing list
immediately if any parts are missing, please contact the service personnel.
2.2
Chassis Interface
|
Description
|
Air outlet side
|
 |
|
Injector drive
|
pin1
|
|
|
Injector drive
|
pin2
|
|
Description
|
Air outlet side
|
 |
|
Injector drive
|
pin1 -
|
|
|
Injector drive
|
pin2 +
|
|
|
Empty
|
pin3
|
|
|
Empty
|
pin4
|
|
|
Description
|
Air
outlet side
|
 |
|
Count
often start
|
Pin1
|
|
|
Counting
common
|
Pin2
|
|
|
Counting
normally closed terminal
|
Pin3
|
3 Operating Instructions
3.1
Chassis panel：
3.2
Basic operation
3.2.1 、Display interface:
BOSCH、DENSO、DELPHI、PIZEO、DENSO2
CL、VL、VE、LL、TL、U1、U2
3、the injector count method:
T:
according to the number of counts;
4、injector counting time:
T :0-2000 times
5、injection signs: icon display indicates the beginning of the
injector fuel injection;
6、pulse width: 100 ~ 5000uS;
7、injection frequency: 1 ~ 30Hz
8、the count flag: Icon display indicates the injector start
counting;
3.2.2
、Key
Features
3.2.2.1
ON/OFF button：
3.2.2.2
COUNTE button:
Start / stop counting.
When the number is 0, the
injector has been working, do not stop;
3.2.2.3
MODE button:
(CL, VL, VE, LL, TL, U1, U2)
B., long press the MODE button to switch between
test patterns and resistance injector test mode;
(Valid only in the injection
stopped)
C, after entering the electronic test mode, first
connect the injector, according to a short Counte key, two seconds later, the
resistance of the injector will be displayed on the screen, in units of
milli-ohms;
D, if found to measure the resistance of the
resistance and the actual deviation is larger, it should be calibrated
Calibration method:
resistance measurement interface, the injector two clips direct short, then
long press "ADJ" button at the top right of the screen there will be
a "*" sign after the symbol disappears, the calibration is complete,
Listed screen display 0 mohm.
3.2.2.4
ADJ
knob:
A. Common parameter settings
Short press down to select the
setting of the project, there is a corresponding position cursor display,
divided into: Injector brand choice / count value / width / frequency, cycle
through the four setting items, the current cursor location for the selected
projects;
The second step,
Rotate Left or Rotate Right, modify the current
value of the item.
3.2.2.5 Language Settings
If the current language is English, first turn
off the power when the screen is off, but according to ON / OFF and MODE key,
then turn on the power, you can read Chinese display;
If the current language is Chinese, first turn
off the power when the screen is off, but according to COUNTE and MODE button,
then turn the power on, the display can be changed to English;
4
About
maintenance responsibility
2、
Due to the non-normal use,
causing damage to the product, the user bear the maintenance costs;
3、
The product life-long
maintenance, a year later, users bear the maintenance costs.
Posted in: 
0 komentar:
Posting Komentar
Catatan: Hanya anggota dari blog ini yang dapat mengirim komentar.