20.41
obd2jombang
EMULATOR EWS support E34 E36 E38 E39 E46 IMMO Immobilizer
INSTALLATION:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:
3. Choose COM port, write in desired ISN number, press button Store. Or –
4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, choose option "EWS emulator" and press button Store to save ISN number into emulator.
5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME(DDE) <-> EWS line.
6. Don't forget to short two starter relay wires (EWS connector)!
7. Car is ready to start.
In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic K-line.
There are NO any counters or car starts limited. You can change and store new ISN without any limitations.
Emulator is shipped with JUMPER 1 shorted. For testing purposes ISN 0579 is stored by default.
download software immo bmw
https://mega.nz/#!oZYBmYID!oG_pBDsCzvj5OtYwhjgtUDVO39RPlpsHN3tUJGk3Szw
EWS EMULATOR FOR B MW
Item: EWS EMULATOR- EWS 2 EWS 3.2 EMULATOR For BM W
INSTALLATION:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and l- aunch EMULATOR
3. Choose COM port, write in desired ISN number, press button Store. Or -
4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, choose option "EWS emulator" and press button Store to save ISN number into emulator.
5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to
DME(DDE) <-> EWS line.
6. Don't forget to short two starter relay wires (EWS connector)!
7. Car is ready to start.
https://mega.nz/#!oZYBmYID!oG_pBDsCzvj5OtYwhjgtUDVO39RPlpsHN3tUJGk3Szw
EWS EMULATOR FOR B MW
Item: EWS EMULATOR- EWS 2 EWS 3.2 EMULATOR For BM W
INSTALLATION:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and l- aunch EMULATOR
3. Choose COM port, write in desired ISN number, press button Store. Or -
4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, choose option "EWS emulator" and press button Store to save ISN number into emulator.
5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to
DME(DDE) <-> EWS line.
6. Don't forget to short two starter relay wires (EWS connector)!
7. Car is ready to start.
Harga : Rp 350.000
Berminat Hubungi :
Nama : Agus yulianto
Alamat : Puri Astapada Indah 2 Blok K/6 RT/RW 03/08 Plosogeneng Jombang, 61416 Jawa Timur
Telp : Simp. 081332787811 xl : 0819391990053 (Whatsapp) pin bb 528285FO
Web :
www.obd2jatim.com
Blog :
http://Toolsteknik.blogspot.com
http://obd2murah.blogspot.com
http://agusyuliato2.blogspot.com
Facebook Agus Yuli Obd Jatim
https://www.facebook.com/obd99
Lokasi toko/rumah Google map
https://mapsengine.google.com/map/edit?mid=zjc70vmO4kjU.kmbc15SqC4NI
Posted in: 
0 komentar:
Posting Komentar
Catatan: Hanya anggota dari blog ini yang dapat mengirim komentar.